Victron Energy – SmartSolar MPPT 250/100-MC4 VE.Can Charge Controller – SCC125110511

$0.00 - 0 items Categories

Hub

Victron Energy – SmartSolar MPPT 250/100-MC4 VE.Can Charge Controller – SCC125110511

  • 250 VOC
  • 100 Amp charger
  • 12/24/48 vdc (auto-detection)
  • Customizable charge settings
  • Warranty- 5yrs
  • Pv reverse polarity protection
  • Output short circuit protection
  • Overtemperature protection

Victron Energy 250/100-MC4 MPPT VE.Can SmartSolar Charge Controller – SCC125110511

The MPPT VE.Can SmartSolar charger uses the latest and fastest technology to convert energy from a solar array into energy that optimally charges battery banks.

The SmartSolar charge controller will even recharge a severely depleted battery. It can operate with a battery voltage as low as 0 Volts, provided the cells are not permanently sulfated or otherwise damaged.

The MPPT VE.Can SmartSolar charger connects to a PV array of 250 Volt Voc and will automatically detect and charge your 12, 24, or 48V battery bank and capable of up to  100 amps of charge.

The charge settings are fully programmable and can even be set up for different battery chemistries, like lead-acid, lithium, and others.

The MPPT VE.Can SmartSolar charger can be remotely controlled and configured over Bluetooth via the VictronConnect App. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, and historical data. 

The VE.Can SmartSolar charger is equipped with CAN bus ports. This allows for communication with additional VE.Can SmartSolar chargers. The additional units are simply “daisy-chained” to each other with a single RJ45 cable between the individual units.

Features: SmartSolar 250/100-MC4 MPPT VE.Can – SCC125110511

  • 250 VOC
  • 100 Amp charger
  • 12/24/48 vdc (auto-detection)
  • Customizable charge settings
  • Warranty- 5yrs

Protections: SmartSolar 250/100-MC4 MPPT VE.Can – SCC125110511

  • Pv reverse polarity protection
  • Output short circuit protection
  • Overtemperature protection

Videos: SmartSolar 250/100-MC4 MPPT VE.Can – SCC125110511

Did You Know - How to change the name of a device

Did You Know – How to change the name of a device?

Did you know you can change the default name in both VictronConnect and VRM? In this did you know video, Jono shows you how.

For technical questions see our support page: https://www.victronenergy.com/support or contact your Victron dealer, distributor, or installer.

You can also have a look at our Victron Community page to see if your question has already been answered there. Or join in the conversation to help others: https://community.victronenergy.com

Did You Know - How to create a battery profile for non-Victron batteries?

Did You Know – How to create a battery profile for non-Victron batteries?

In this Did You Know, Marianka from Victron Energy explains how to create a battery profile for non-Victron batteries.

For technical questions see our support page: https://www.victronenergy.com/support or contact your Victron dealer, distributor, or installer.

Did You Know - Trigger a dump load when your batteries are full

Did You Know – Trigger a dump load when your batteries are full

If you have an MPPT or a Victron MultiPlus, you can set it so that when your batteries are full, a load is triggered to make use of excess solar. Johannes goes into more detail in this Did You Know

For technical questions see our support page: https://www.victronenergy.com/support or contact your Victron dealer, distributor, or installer.

Did you know...why the MPPT charge controller starts 5Vdc above the battery voltage?

Did you know…why the MPPT charge controller starts 5Vdc above the battery voltage?

You can find a more detailed explanation here: https://www.youtube.com/watch?v=uTMVmW7GTus

For technical questions see our support page: https://www.victronenergy.com/support or contact your Victron dealer, distributor, or installer.

Documents: SmartSolar 250/100-MC4 MPPT VE.Can – SCC125110511

FAQs: SmartSolar 250/100-MC4 MPPT VE.Can – SCC125110511

☁️ Does SmartSolar 250/100-MC4 MPPT VE.Can have output short circuit protection?

🔎 Yes. SmartSolar 250/100-MC4 MPPT VE.Can has output short circuit protection as well as PV reverse polarity protection and overtemperature protection.

☁️ Is it possible to create user-defined battery presents with SmartSolar 250/100-MC4 MPPT VE.Can charge controllers?

🔎 Yes, it is possible to also create user-defined battery presets. The chapter Customize battery charge algorithm [19] explains how to do this. These user-defined presets are stored in the VictronConnect App library. This is helpful in case multiple solar chargers need to be configured, eliminating the need to define the entire charge algorithm each time a new solar charger is configured.

☁️ How many years of warranty does Victron Energy provide for the SmartSolar 250/100-MC4 MPPT VE.Can charge controllers?

🔎 SmartSolar 250/100-MC4 MPPT VE.Can – SCC125110511 come with 5 years of warranty.

How To Buy: SmartSolar 250/100-MC4 MPPT VE.Can

If you are ready to buy an SCC125110511 maximum power point tracking charge controller SmartSolar 250/100-MC4 MPPT VE.Can (SCC125110511), simply register for a free account with us – your off-grid Victron Energy Charge Controller supplier; Zonna Energy – and wait for us to contact you within 24 – 48 business hours to authorize your dealer account. After you’ve registered, you’ll be able to take advantage of wholesale rates and same-day shipping choices. (Some items may qualify for next-day delivery.) Click the link below and fill out the form to establish an account. We would gladly help you with your Victron Energy – 250/100-MC4 MPPT VE.Can SmartSolar Charge Controller – SCC125110511 purchase.